无法下载 polarssl-1.3.9-gpl.tgz 导致 openwrt 编译失败

This topic created in 4198 days ago, the information mentioned may be changed or developed.

想给RY-1编译定制的openwrt固件，可是编译失败。打开V=s重新编译了一次，失败退出前显示如下信息：

--2014-11-23 12:50:48-- https://polarssl.org/code/releases/polarssl-1.3.9-gpl.tgz
Resolving polarssl.org (polarssl.org)... 79.170.91.36
Connecting to polarssl.org (polarssl.org)|79.170.91.36|:443... connected.
HTTP request sent, awaiting response... 200 OK
Length: 1741396 (1.7M) [application/x-gzip]
Saving to: 'STDOUT'

37% [==============================================> ] 655,280 85.9KB/s in 7.4s

2014-11-23 12:50:58 (85.9 KB/s) - Connection closed at byte 655280. Retrying.

--2014-11-23 12:50:59-- (try: 2) https://polarssl.org/code/releases/polarssl-1.3.9-gpl.tgz
Connecting to polarssl.org (polarssl.org)|79.170.91.36|:443... connected.
HTTP request sent, awaiting response... 200 OK
Length: 1741396 (1.7M) [application/x-gzip]
Saving to: 'STDOUT'

30% [=====================================> ] 524,224 74.9KB/s in 6.8s

2014-11-23 12:51:07 (74.9 KB/s) - Connection closed at byte 655280. Retrying.

--2014-11-23 12:51:09-- (try: 3) https://polarssl.org/code/releases/polarssl-1.3.9-gpl.tgz
Connecting to polarssl.org (polarssl.org)|79.170.91.36|:443... connected.
HTTP request sent, awaiting response... 200 OK
Length: 1741396 (1.7M) [application/x-gzip]
Saving to: 'STDOUT'

18% [======================> ] 326,624 52.2KB/s in 6.1s

2014-11-23 12:51:18 (52.2 KB/s) - Connection closed at byte 655280. Retrying.

--2014-11-23 12:51:21-- (try: 4) https://polarssl.org/code/releases/polarssl-1.3.9-gpl.tgz
Connecting to polarssl.org (polarssl.org)|79.170.91.36|:443... connected.
HTTP request sent, awaiting response... 200 OK
Length: 1741396 (1.7M) [application/x-gzip]
Saving to: 'STDOUT'

11% [=============> ] 195,568 29.7KB/s in 6.4s

2014-11-23 12:51:29 (29.7 KB/s) - Connection closed at byte 655280. Retrying.

--2014-11-23 12:51:33-- (try: 5) https://polarssl.org/code/releases/polarssl-1.3.9-gpl.tgz
Connecting to polarssl.org (polarssl.org)|79.170.91.36|:443... connected.
HTTP request sent, awaiting response... 200 OK
Length: 1741396 (1.7M) [application/x-gzip]
Saving to: 'STDOUT'

13% [===============> ] 229,352 36.8KB/s in 6.1s

2014-11-23 12:51:41 (36.8 KB/s) - Connection closed at byte 655280. Giving up.

Download failed.
--2014-11-23 12:51:41-- http://mirror2.openwrt.org/sources/polarssl-1.3.9-gpl.tgz
Resolving mirror2.openwrt.org (mirror2.openwrt.org)... 46.4.11.11
Connecting to mirror2.openwrt.org (mirror2.openwrt.org)|46.4.11.11|:80... connected.
HTTP request sent, awaiting response... 404 Not Found
2014-11-23 12:51:43 ERROR 404: Not Found.

Download failed.
--2014-11-23 12:51:43-- http://downloads.openwrt.org/sources/polarssl-1.3.9-gpl.tgz
Resolving downloads.openwrt.org (downloads.openwrt.org)... 78.24.191.177
Connecting to downloads.openwrt.org (downloads.openwrt.org)|78.24.191.177|:80... connected.
HTTP request sent, awaiting response... 404 Not Found
2014-11-23 12:51:48 ERROR 404: Not Found.

Download failed.
No more mirrors to try - giving up.

请问应该如何解决呢？

connecting

awaiting

connected

18 replies • 2015-07-25 12:05:05 +08:00

shangjiyu

Nov 23, 2014

http://pan.baidu.com/s/1hdJX0

xiaofami

Nov 23, 2014

@shangjiyu 下载之后如何让编译程序找到这个文件呢？

xiaofami

Nov 23, 2014

@shangjiyu 解决了。把那个文件手动下载后，丢到./openwrt/dl目录下即可。

shangjiyu

Nov 30, 2014

编译的怎么样了?

xiaofami

Dec 1, 2014

@shangjiyu 编译成功。shadowsocks、Ramod以及openvpn、openconnect等都编译进固件了。自己还使用apache搭建了一个本地软件源，用起来挺方便。不过VPS上搭建ocserv的实验没有成功，总是报无法读取证书，无解ing...

shangjiyu

Dec 1, 2014

@xiaofami 可以的，可以告知怎么编译如意云么？我在 trunk 下编译，没有 mt7620n 这个选项了，貌似合并进7620了，然后按照 RT-N14U做了个 default16M 的 RY-1 profile编译出来后只有 sysupgrade.bin刷进去直接板砖。。。

xiaofami

Dec 2, 2014

@shangjiyu 好的。

1.环境：Linuxmint 17

2.在～/下执行 git clone git://git.openwrt.org/openwrt.git
会生成目录openwrt

3. cd openwrt

4.如果想引进Shadowsocks和Ramod，打开 openwrt/feeds.conf.default 这个文件，添加

src-git ramod https://github.com/ravageralpha/my_openwrt_mod.git
src-git shadowsocks https://github.com/clowwindy/shadowsocks.git

5.在openwrt/下执行
./scripts/feeds update -a
./scripts/feeds install -a

6.执行

make defconfig
make prereq

检查编译环境是否完整，以及其他的错误信息。如果你在执行 make defconfig 后遇到类似 “Do not support multiline”之类的信息，检查～/openwrt/tmp.config-package 这个文件，有一个地方丢了一个引号，自己加上就好。

7.执行

make menuconfig

Target System 选 Ralink RT288x/RT3xxx，Subtarget 选 MT7620n based boards。之后的选择就看个人需求了。注意固件大小不能超过16MB，否则默认配置下不会生成固件。类似

openwrt-ramips-mt7620n-rt-n14u-squashfs-sysupgrade.bin
openwrt-ramips-mt7620n-wrtnode-squashfs-sysupgrade.bin
openwrt-ramips-mt7620n-mlw221-squashfs-sysupgrade.bin
openwrt-ramips-mt7620n-wr8305rt-squashfs-sysupgrade.bin

等等都是可以用来在Uboot下刷机的固件。我测试过前面两个，在LuCI的系统概况下会显示为不同的路由器，其它方面倒是没发现区别。

xiaofami

Dec 2, 2014

～/openwrt/tmp.config-package 应为～/openwrt/tmp/.config-package 。

还有，make menuconfig 后的配置文件名用默认的 .config 就好，我不知道怎样让编译程序找到改名后的config文件～

xiaofami

Dec 2, 2014

还有一点，tor的编译一直有问题，解决了的话告诉一下解决方法哈～

shangjiyu

Dec 2, 2014

@xiaofami 看来你用的不是trunk， trunk最新合并了7620n和a, 默认RT-N14U是8M的固件，还有就是无线有驱动了？

xiaofami

Dec 2, 2014

@shangjiyu RY-1无线驱动在默认可用，不需要额外设置。

xiaofami

Dec 9, 2014 via Android

@shangjiyu 我用的是trunk的代码呀，编译出的固件代号是Chaos Claimer，wiki上有写。更新代码后检查了一下，没发现MT7620n/a合并～

shangjiyu

Dec 9, 2014

@xiaofami 已经合并了, 这个changeset做的 https://dev.openwrt.org/changeset/43300
另外 led灯配置不对，你又它的dts补丁么？

xiaofami

Dec 9, 2014

@shangjiyu 看到了。不过我更新到最新的trunk代码，menconfig中Ralink RT288x/RT3xxx的Sub Target中还是有独立的mt7620n和mt7620a。根据这里的提示获取的trunk代码：

https://dev.openwrt.org/wiki/GetSource

RY-1的dts补丁没有，不过应该能自行配置LED灯，可以参考一下
http://n-dimensional.de/blog/2014/07/04/led-configuration-with-openwrt/

shangjiyu

Dec 9, 2014

@xiaofami 你可能没有删除 temp/ 这个目录
关于led的问题必须在dts里面定义好了gpio和led的关系才能在openwrt里面设置吧，没有enable对应的gpio你设置了也没有用吧
参考：
http://wiki.wrtnode.com/index.php?title=GPIO%E5%A4%8D%E7%94%A8%E5%BC%95%E8%84%9A%E7%9A%84%E9%87%8A%E6%94%BE%E5%8F%8Agpio-leds%E7%9A%84%E6%B3%A8%E5%86%8C

brightsm

Dec 25, 2014

我的兔兔飞路由器用的是mt7620n的cpu 32M sdr 我改的8M spiflash ，刷openwrt-ramips-mt7620n-rt-n14u-squashfs-sysupgrade.bin
openwrt-ramips-mt7620n-wrtnode-squashfs-sysupgrade.bin
openwrt-ramips-mt7620n-mlw221-squashfs-sysupgrade.bin
openwrt-ramips-mt7620n-wr8305rt-squashfs-sysupgrade.bin
都启动不了，都是显示start kenel就完了。
刷pandurao BOX MW305R的固件可以启动，我就想自己编译一个固件，可是就是得不到正确的固件。大侠分析一下。
失败的UBOOT信息
*** Warning - bad CRC, using default environment

Clocks: CPU:600MHz, Bus:120MHz
In: serial
Out: serial
Err: serial
Net: rt2880_eth_initialize...
VLAN: None
Fetching MAC Address from 0xbc040028
eth0: 34:bd:f9:8a:7f:94
eth0 up
eth0
Hit any key to stop autoboot: 0
## Booting image at 9c050000 ...
Image Name: MIPS OpenWrt Linux-3.10.49
Created: 2014-10-01 14:48:27 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1080184 Bytes = 1 MB
Load Address: 80000000
Entry Point: 80000000
Verifying Checksum at 0x9c050040 ... OK
Uncompressing Kernel Image ... OK

Starting kernel ...

panduora box启动信息：
PandoraBox For Ralink SoC. Copyright 2005-2013 Lintel<[email protected]>

Linux Kernel started...

THIS IS ASIC
[ 0.000000] Linux version 3.4.54 (lintel@lintel-ThinkPad-T430) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #11 Sat Aug 3 03:53:37 CST 2013
[ 0.000000] MediaTek MT7620N CPU:600MHz, Bus:150MHz Uart:40MHz
[ 0.000000] Boot form:SPI FLASH
[ 0.000000] MIPS CPU sleep mode enabled.
[ 0.000000] Detecting memory...32 MB!
[ 0.000000] PCIE: bypass PCIe DLL.
[ 0.000000] PCIE: Elastic buffer control: Addr:0x68 -> 0xB4
[ 0.000000] disable all power about PCIe
[ 0.000000] PCIE: PLL power down for MT7620N
[ 0.000000] CPU revision is: 00019650 (MIPS 24KEc)
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00002000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00002000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: console=ttyS1,115200n8 board=MW305R rootfstype=squashfs
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 29324k/32768k available (2353k kernel code, 3444k reserved, 389k data, 160k init, 0k highmem)
[ 0.000000] SLUB: Genslabs=9, HWalign=16, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:128
[ 0.000000] MTK/Ralink System Tick Counter init... cd:8029f170, m:214748, s:32
[ 0.000000] console [ttyS1] enabled
[ 0.010000] Calibrating delay loop... 398.13 BogoMIPS (lpj=1990656)
[ 0.070000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 512
[ 0.080000] NET: Registered protocol family 16
[ 0.090000] MIPS: machine is Mercury MW305R
[ 0.090000] Ralink Board GPIO_MODE init:
[ 0.090000] I2C:GPIO
[ 0.100000] SPI_REFCLK:GPIO
[ 0.100000] UART_F:GPIO
[ 0.100000] GPIO_MODE_REGs: 0xa311d
[ 0.100000] ralink_register_flash:SPI Flash.
[ 0.110000] General GPIO Driver for MediaTek MT7620N Board. Copyright lintel<[email protected]> 2005-2013
[ 0.120000] gpiochip_add: registered GPIOs 0 to 23 on device: MT7620-GPIO0
[ 0.120000] gpiochip_add: registered GPIOs 24 to 39 on device: MT7620-GPIO1
[ 0.130000] gpiochip_add: registered GPIOs 40 to 71 on device: MT7620-GPIO2
[ 0.130000] gpiochip_add: registered GPIOs 72 to 95 on device: MT7620-GPIO3
[ 0.230000] MT7620 PPLL unlock
[ 0.250000] bio: create slab <bio-0> at 0
[ 0.260000] Switching to clocksource Ralink external timer
[ 0.270000] NET: Registered protocol family 2
[ 0.270000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.270000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.280000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.290000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.290000] TCP: reno registered
[ 0.300000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.300000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.310000] NET: Registered protocol family 1
[ 0.310000] Ralink SoC clocks api init.
[ 0.320000] Ralink GPIODEV resource maped.
[ 0.320000] RT3xxx EHCI/OHCI init.
[ 0.350000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.360000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) © 2001-2006 Red Hat, Inc.
[ 0.370000] msgmni has been set to 57
[ 0.370000] io scheduler noop registered
[ 0.380000] io scheduler deadline registered (default)
[ 0.380000] io scheduler cfq registered
[ 0.390000] Ralink DMA Engine API Enable .
[ 0.390000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled

brightsm

Dec 25, 2014

[ 0.400000] serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A
[ 0.410000] serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A
[ 0.410000] Enable Ralink GDMA Controller Module
[ 0.420000] GDMA IP Version=3
[ 0.430000] loop: module loaded
[ 0.440000] Ralink SPI flash Driver for PandoraBox.
[ 0.440000] deice id : c2 20 17 c2 20 (2017c220)
[ 0.450000] MX25L6405D(c2 2017c220) (8192 Kbytes)
[ 0.450000] mtd .name = raspi, .size = 0x00800000 (0M) .erasesize = 0x00000008 (0K) .numeraseregions = 65536
[ 0.460000] Creating 5 MTD partitions on "raspi":
[ 0.470000] 0x000000000000-0x000000030000 : "u-boot"
[ 0.470000] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.480000] 0x000000040000-0x000000050000 : "Factory"
[ 0.490000] 0x000000000000-0x000000800000 : "fullflash"
[ 0.500000] 0x000000050000-0x000001000000 : "firmware"
[ 0.500000] mtd: partition "firmware" extends beyond the end of device "raspi" -- size truncated to 0x7b0000
[ 0.520000] Creating 2 MTD partitions on "raspi":
[ 0.520000] 0x000000050000-0x000000140000 : "kernel"
[ 0.530000] 0x000000140000-0x000001000000 : "rootfs"
[ 0.530000] mtd: partition "rootfs" extends beyond the end of device "raspi" -- size truncated to 0x6c0000
[ 0.550000] mtd: partition "rootfs" set to be root filesystem
[ 0.550000] mtd: partition "rootfs_data" created automatically, ofs=6B0000, len=150000
[ 0.560000] 0x0000006b0000-0x000000800000 : "rootfs_data"
[ 0.570000] rdm_major = 253
[ 0.570000] EEPROM:Read from [Factory] offset 0x28,length 0x6.
[ 0.580000] SMACCR1 -- : 0x0000000c
[ 0.580000] SMACCR0 -- : 0x43762077
[ 0.580000] Ralink APSoC Ethernet Driver Initilization. v3.0 64 rx/tx descriptors allocated, mtu = 1500!
[ 0.590000] EEPROM:Read from [Factory] offset 0x28,length 0x6.
[ 0.600000] SMACCR1 -- : 0x0000000c
[ 0.600000] SMACCR0 -- : 0x43762077
[ 0.610000] PROC INIT OK!
[ 0.610000] Ralink APSoC Hardware Watchdog Timer
[ 0.620000] sdhci: Secure Digital Host Controller Interface driver
[ 0.620000] sdhci: Copyright(c) Pierre Ossman
[ 0.630000] SDHC Interface init.
[ 0.630000] mtk-sd: MediaTek MT76xx MSDC Driver
[ 0.640000] sdhci-pltfm: SDHCI platform and OF driver helper
[ 0.650000] TCP: cubic registered
[ 0.650000] NET: Registered protocol family 17
[ 0.650000] 8021q: 802.1Q VLAN Support v1.8
[ 0.670000] VFS: Mounted root (squashfs filesystem) readonly on device 31:6.
[ 0.680000] Freeing unused kernel memory: 160k freed
##### MediaTek MT76xx ESW VLAN Partition(12345) #####
switch reg write offset=2004, value=ff0003
switch reg write offset=2104, value=ff0003
switch reg write offset=2204, value=ff0003
switch reg write offset=2304, value=ff0003
switch reg write offset=2404, value=ff0003
switch reg write offset=2504, value=ff0003
switch reg write offset=2010, value=810000c0
switch reg write offset=2110, value=810000c0
switch reg write offset=2210, value=810000c0
switch reg write offset=2310, value=810000c0
switch reg write offset=2410, value=810000c0
switch reg write offset=2510, value=810000c0
switch reg write offset=2610, value=81000000
switch reg write offset=2710, value=81000000
switch reg write offset=2604, value=20ff0003
switch reg write offset=2704, value=20ff0003
Special Tag Disabled
switch reg write offset=2610, value=81000000
12345
switch reg write offset=2014, value=10001
switch reg write offset=2114, value=10002
switch reg write offset=2214, value=10003
switch reg write offset=2314, value=10004
switch reg write offset=2414, value=10005
switch reg write offset=2514, value=10006
REG_ESW_WT_MAC_ATC is 0x7ff0002
done.
[ 2.950000] Button Hotplug driver version 0.4.1
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
[ 6.340000] jffs2: notice: (442) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 51 of xref (0 dead, 32 orphan) found.
[ 6.930000] SCSI subsystem initialized
[ 7.090000] usbcore: registered new interface driver usbfs
[ 7.090000] usbcore: registered new interface driver hub
[ 7.100000] usbcore: registered new device driver usb
[ 7.660000] xfs: Unknown symbol exportfs_decode_fh (err 0)
[ 7.760000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 7.780000] rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller
[ 7.790000] rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1
[ 7.830000] rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x101c0000
[ 7.850000] rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00
[ 7.85

jeromeli

Jul 25, 2015

http://buildbot.openwrt.org:8010/src/

这里面好像有吧